Shed plans 10×12, with gable roof. Plans include a free PDF download (link at bottom of blog post), step-by-step details, drawings, measurements, shopping list, and cutting list.
Shed Plans 10×12 Gable Shed – Overview
Shed Plans 10×12 Gable Shed – Material List
Shopping List
Shopping List
(material for door & window not included below)
Floor
2 – pressure treated 2×6 – 12′
10 – pressure treated 2×6 – 10′
3 – pressure treated 4×4 – 12′
4 – 3/4″ tongue and groove plywood – 4’x8′ sheet
Wall Frames
6 – 2×4 – 12′
46 – 2×4 – 8′
6 – 2×4 – 10′
Roof Frame – Rafters/Truss
28 – 2×4 – 8′
10 – 2×4 – 10′
Siding
13 – 5/8″ t1-11 exterior siding – 4’x8′ sheet
Roof Trim
4 – 2×6 – 8′
Roof Deck
8 – 1/2″ plywood – 4’x8′ sheet
Corner Trim
4 – 1×4 – 8′
4 – 1×4 – 10′
Hardware
3 1/2″ galvanized nails
2″ deck screws
2″ galvanized nails
1 1/4″ galvanized finishing nails
shingles
roof tacks
roofing felt
staples
drip edge
Cutting List
Cutting List
(material for door & window not included below)
Floor
2 – pressure treated 2×6 – 12′
10 – pressure treated 2×6 – 9′ 9″
3 – pressure treated 4×4 – 12′
4 – 3/4″ tongue and groove plywood – 4’x8′ sheet (cut to size)
Wall Frames
4– 2×4 – 12′
2 – 2×4 – 11′ 5″
46– 2×4 – 7′ 6″
4 – 2×4 – 9′ 5″
2 – 2×4 – 10′
Rafters/Truss
20– 2×4 – 6′ 7 5/16″
10 – 2×4 – 2′ 2 7/16″
10 – 2×4 – 10′
12 – 2×4 – 2′ 1 3/4″
Siding
13– 5/8 t1-11 exterior siding – 4’x8′ sheet (cut to size)
Roof Trim
4– 2×6 – 6′ 7 5/16″
Roof Deck
8– 1/2″ plywood – 4’x8′ sheets (cut to size)
Corner Trim
4 – 1×4 – 8′ (cut to size)
4 – 1×4 – 10′ (cut to size)
The shed floor is built with pressure treated 2×6 and pressure treated 4×4 lumber.
Cut two 2×6’s to 12′ long for the band. Cutten 2×6’s to 9′ 9″ long for the floor joist. Nail 3 1/2″ nails through the 2×6 band and into the floor joist. Space floor joist 16″ O.C.
Attach the 12′ long 4×4 pressure treated skids to the bottom of the floor frame. Square out the floor frame by measuring diagonally until both sides measure the same. Secure the 4×4 skids by nailing 3 1/2″ nails through the floor frame and into the 4×4 skids.
Cut to size and install the 3/4″ tongue and groove plywood to the floor frame. Secure the floorplywood deck with 2″ deck screws.
The front and back wall frame is built using 2×4 lumber.
The wall studs are spaced 16″ O.C.
Assemble the back wall frame as shown on illustration above (see illustration below for close up view).
The front wall frame will have a door and window, for instructions on framing the door and window see the pages below:
- Shed Door Plans
- Wall Framing – Adding a Shed Window
Assemble the front and back wall frame using 3 1/2″ nails.
Here is a close up look of the front and back wall frame ends.
Cut the 2×4’s as shown on illustration above for the side walls.
Wall studs are spaced 16″ O.C.
If you will be adding a double door to the side wall of the shed, see this page for door details: Shed Door Plans
Assemble the side wall frame using 3 1/2″ nails.
Truss and rafter details.
The truss is built using 2×4 lumber.
Cut the 2×4’s as shown on illustration above. The trussis assembled using 1/2″ plywood gussets. Nail 2″ nails through the gusset and into the truss.
Attach the truss to the shed 16″ O.C. Toenail 3 1/2″ nails through the truss and into the wall frame.
Cut to size and install the siding using 1 1/4″ finishing nails. Install doors, and windows.
To build the 1′ overhand cut the 2×4’s outriggers as shown above. Notch as shown on illustration above and install the outriggers using 3 1/2″ nails.
Once the outriggers have been installed cut to size the 2×6 lumber for theroof trim as shown on illustration above and install with 3 1/2″ nails.
Cut 2×4 blocksto size and install between the rafters with 3 1/2″ nails.
Cut t1-11 siding to size and install between the rafters as shown on illustration above. Use 1 1/4″ finishing nails to install.
Measure, cut, and install the 1/2″ plywood for the roof deck.
Install the roofing felt, drip edge, and shingles.
Install the 1×4 trim corner trim.
Like these 10×12 shedplans? Let me know, leave me a comment below. Share this link with your friends and your social media, thanks.
PDF DOWNLOAD
- Shed Plans 10×12 Gable Shed – PDF Download
Download
- 10×12 Lean To Shed Plans – PDF Download
Download
- 10×12 Barn Shed Plans – PDF Download
Download
Related Articles
DIY Double Chair Bench With Table
DIY 2×4 Planter Box | How To Plans
DIY 2-in-1 Bird House and Feeder
8×8 Pergola Plans
DIY Rotating Pegboard Display
DIY Walk In Bird Aviary | 8×16 Plans
69 comments
Heath
March 28, 2017 at 6:34 am
Really like the plan but as a novice joiner do you have anything a bit more basic
Reply
Rick Bell
July 30, 2017 at 3:43 pm
There is plenty of videos on how to construct these. Even beginners can cut the boards to the right sizes needed for the most difficult parts, Roof truss. Go to youtube and fill in search area with your size shed and you can watch many of them being built and explained for you the details. You can also build these without any over hang which makes it easier as well.
Reply
Johnny
August 20, 2020 at 5:44 pm
Could I make a birdsmouth instead of using the 10 ft board across the truss of so do you know where?
Reply
Dan
August 20, 2020 at 6:26 pm
Search for “Gable Roof Framing Calculator” on google, it will help you design the truss the way you want.
Reply
Johnny
August 22, 2020 at 8:53 pm
So I did a step of method Wich was easier than the deed square took me 4 trys but I got it framed.
Reply
Erik
April 24, 2017 at 8:13 pm
Awesome plans but, can you make a 10×12 lean to shed plan? Please?
Reply
Jose Nilo
April 28, 2017 at 11:53 am
How do I download a project
Reply
Rick Bell
July 30, 2017 at 3:45 pm
Just click on the size you want and it automatically shows the plans, the material lists and cuts. I didn’t have to down load mine. Anytime you see download beware though as you could be downloading something that is not the plans or instructions but something tied to these that publishers trick people into loading on their computers.
Reply
Asfaha
June 9, 2019 at 6:54 am
06/09/2019
Hello. Your website and the plans provided here are awesome. Thank you very, very much. I am planning to build the 10 × 12 garden shed next week , thanksReply
Jose Nilo
April 28, 2017 at 11:54 am
Help anybody , how can I download a project
Reply
Brett Youlten
July 2, 2017 at 6:32 pm
create account ..add project to cart/checkout it will be sent to your email
Reply
Jeff
August 2, 2017 at 3:28 pm
Hello. Your website and the plans provided here are awesome. Thank you very, very much. I am planning to build the 8×8 garden shed this month, with a due date of September 1st.
Question… Is is possible to obtain a copy of the sketchup file for this 8×8 Garden Shed? Thanks for your time.
Reply
Matthew
October 3, 2017 at 5:36 pm
Thanks for the plans! Very easy to follow and construct. This was my first attempt building a shed and the framing went a lot easier than I thought. I did it all by myself so it took me three weekends to complete. The only thing I hd to research more was how to shingle a shed but there was plenty of videos on YouTube to help me out. I put some extra trim on my shed to spruce it up a little more. Thanks again for the plans I enjoyed building it.
Reply
Chris
January 7, 2018 at 1:47 am
Can you show me a side view with the bigger door? Looks fantastic. This is exactly what I’m looking to do and I think this is a better choice than the ones at Home Depot. Thank you
Reply
Matthew
April 9, 2018 at 5:41 pm
Here is the side view. I didn’t construct the roof overhang on the backside of the shed since this was facing towards the woods. I looked at the sheds at Home Depot and Lowes. They are good if you want something quick, but I wanted something that would last and I wanted more head room. This shed is perfect and it was easy to build and gives me 8 feet of head room.
Reply
Grx
April 17, 2018 at 9:20 am
This will be my first building project. For the materials, do you recommend a lumber yard? I’m coming up with a different figure of around $1650 for the shell alone through a place like lowes.
Reply
Rick P. ("I Wood if I Could")
July 25, 2018 at 8:47 am
Different suppliers offer different qualities of products and you get what you pay for. Lowes typically has a better grade of building products, but this is a shed. It is unlikely that you are going to drywall the inside or other things that would warrant the best lumber. That being said, you can usually get pretty good wood, etc at the lower priced retailers with a little sorting through the woodpile. The things that will show — such as the exterior trim — might be nicer with better wood, but remember that caulk and good paint work wonders.
Rod
March 21, 2018 at 9:41 am
Hi,
Can you give me an idea of what your total cost was? I trying to weight the difference of making one or just buying one.
Thanks in advance.
RodReply
Matthew
April 9, 2018 at 6:19 pm
My total cost was just around $1,400 (I already had a window and door which I used on the front of the shed). I know you could make this shed much cheaper (probably under $1,000) but i used exterior 3/4 plywood for the floor and 3/4 exterior siding (and pressure treated lumber for the base structure and the wall studs). I also used plywood and architectural shingles for the roof. The base and flooring of the structure ran me about $300 (sheathing, 2×6’s and screws), the siding was about $400 (it was $50 per sheet and you need 8). The lumber and nails for the walls and roof trusses was about $275. The roof (with shingles, felt paper and drip edge) cost about $250. Then about another $200 for the trim boards, benjamin moore stain, hinges, and a lock set. I do need to still make a ramp for the side so it is easier for my tractor and snowblower to get in and out. (I had fun building this shed and the plans were easy to follow or modify). If you have the time (a couple of weekends) and like to take on a project then I would say make the shed you won’t be disappointed. This shed is solid and probably one in similar quality would have cost me around $3,000 in my opinion (I live in NY). (If you do build it think about asking a friend to help out for a weekend. I built this myself but it would have been nice to have an extra hand when it came time to installing the roof (would save you a lot of trips going up and down the ladder).
Reply
Ian
April 14, 2018 at 7:15 pm
Hi Matthew,
Can you confirm that the material list under the Wall Frames section that calls for 6- 2x6x10 is wrong and they mean 6- 2x4x10? I was so confused at the store until I realized when I got home that in the cutting list it seems to switch to 4- 2x4x9.5 and 2- 2x4x10.
Thanks,
IanReply
Jake
April 14, 2018 at 10:07 pm
It is wrong, it should read 2×4, fixed it, thanks.
Albert Pasquale
April 24, 2020 at 8:02 am
I would like to see your price list because there is noway in NJ you will be able to build this shed for under $1000 I am up too $1600 without any doors or windows or paint
Reply
Steve
April 28, 2022 at 11:19 am
And how much does it weigh? Need to move it with a skidsteer.
Reply
Dan Patterson
January 23, 2018 at 10:52 pm
Can the roof trusses be modified to accommodate a loft?
Reply
Rick P. ("I Wood if I Could")
July 25, 2018 at 9:22 am
I built my trusses from 2×6’s and left out the King Posts. I used some hurricane ties and additional blocking to make sure the roof was strong. Then you can floor the “loft” to suit your needs. I would recommend that you put the plywood floor in place before you roof the shed. The first time I built one of these, I had to cut my plywood up a little to get it between the trusses.
Reply
Bryanna
January 31, 2018 at 7:33 pm
Is this able to be modified easily to be longer or wider?
Reply
bill emery
February 2, 2018 at 6:15 pm
if i pour a concrete driveway up to the shed how do i keep water from going under it? the shed will have pavers on one side and concrete on the other with dirt on the other 2 sides
Reply
Raymond
March 4, 2018 at 10:46 am
It doesn’t say in the plans if the tongue and groove floor plywood is Pressure treated is that recommed or could you use just regular t&g since its already so high off the ground.
Reply
Jason W Boice
May 4, 2018 at 9:33 pm
I would recommend pressure treated. It costs a little more but it will protect the floor above and below.
Reply
Dan Sholy
April 12, 2018 at 7:09 pm
How would you secure this to a windy area with frost line? I live up north.
Reply
Ken Kerr
September 21, 2019 at 2:18 pm
Dan,
I have the same problems, windy and cold winters. I think twelve 4×4 concrete piers as close to the ground as possible allowing all to be levelled. I will add 6 inches of a 4×4 with a hole in the middle. I can attach the 2×6 inch floor joists to the six inches of 4×4 and drive rebar down through the hole securing all the piers.
Reply
Jason W Boice
May 4, 2018 at 9:30 pm
Very nice plans, great job. I am moderate-semi experienced in carpentry so these plans just made the job a little easier, especially the supplies list. I added windows to both sides instead of the front. Built the whole thing by myself in 5 loooong days. Built the door myself, I wanted it big so it’s a single 40×78″ with 4 heavy duty hinges.
Reply
Robin
August 7, 2018 at 2:13 pm
I’m a beginner. I see the wall frame, but I don’t see how to attach the window and door to the wall.
What are the measuements for the window?
What are the measurments for the door?
What I mean is, how tall and how wide are the window and door?
Should I purchase the window first, then make sure the same size is cut out of the wall framing?
Are some steps missing?Reply
Ozan
July 7, 2019 at 7:30 am
If you buy the plans, there will be three pdfs, one for the shed, one for doors and one for windows.
Reply
David Motry
February 3, 2019 at 2:07 pm
Really like the plans. now I can put together a cost so i can convince my wife it is better to build on a concrete floor rather than buy pre built on skids for more money. (hopefully). I did have trouble navigating the “my converter hub” download. Thanks for providing these plans. I hope all the clicks don’t me in trouble later.
Reply
Dwayne Worden
April 7, 2019 at 6:52 am
Outstanding! Plans are super easy to follow and laid out concisely. I’ll definitely check out more of your plans.
Reply
Michael Long
June 13, 2019 at 11:05 am
Thanks for the shed amazing step by step plans. I was wondering if you knew how many pounds of the hardware(nails, screws, tacks and staples) you would need?
Reply
Tom
June 28, 2019 at 10:11 am
How much should this plan realistically cost?
Reply
Michael Johnson
July 1, 2019 at 10:34 am
Rough cost of supplies? I am thinking over 500.00 perhaps 1000+?
Reply
Linann Dumayas
July 19, 2019 at 12:35 am
Hi, you have beautiful shed. Thank you so much for the instructions. I like to build this shed. Show how can’t download the pdf? How do I download this plan shed? Please help! You’re awesome!! Thank you!
Reply
Jack Kritzer
August 31, 2019 at 6:36 am
The 10′ wall stud placement doesn’t line up with the 4×8 siding placement shown on the pictures? Am I wrong?
Reply
Lynn
September 26, 2019 at 9:31 am
I know that this probably sounds like a dumb comment, but you might want to clarify how the length dimensions for boards that are cut on an angle (for roof trusses) are measured.
Is the dimension shown the shortest edge or the longest edge?Reply
John 3:16
September 26, 2019 at 12:50 pm
Dimension is for the long edge.
Reply
Kurt Canez
January 29, 2020 at 9:59 am
Can you give me a ballpark estimate of material costs for this shed?
I’m in Northern CaliforniaReply
Mark Von Thaden
May 4, 2020 at 10:08 pm
I just purchased the materials and will be building the shed starting this weekend I grabbed a few extra 2×4 studs just in case and it ran (with hardware and nails) about $1150 from Home Depot. I am near Sacramento.
Reply
Ken
February 28, 2020 at 3:17 pm
Has anyone purchased the materials through a big box store like Lowes or Home Depot? What was your all in material cost?
Reply
Mark Von Thaden
May 4, 2020 at 10:09 pm
I just purchased the materials and will be building the shed starting this weekend I grabbed a few extra 2×4 studs just in case and it ran (with hardware and nails) about $1150 from Home Depot. I am near Sacramento.
Reply
Renegade7
March 18, 2020 at 11:46 am
If I modify these plans, and go 8×10 foot shed, can I use 2×4 floor joists or should I stay at 2×6? Also, would you stay with 16 in centers on the floor joist?
Reply
Lawrence Warren
March 20, 2020 at 7:03 pm
They have 8×10 plans, the reason for the larger board’s is the size. I’d personally would go with the larger shed if you have the room. Also depending on how long you want the shed to last, not sag, etc. If you will be moving in the next 5 to 8 years you would be fine doing 2x4s. If you are staying dont skimp out playa
Reply
John
April 12, 2020 at 6:16 pm
Do you know the measurement from the interior finished floor to the highest ceiling point based on these measurements? I have to keep it under 10’ from “finished floor” to highest “average roof height”. Wondering if these measurement will work or if I need to modify. Thank you!
Reply
Elizabeth McCoy
May 10, 2020 at 9:02 am
Very helpful, thank you.
Reply
Brandt
May 11, 2020 at 7:38 am
Based on the 26.5degree truss angle, shouldn’t the length of the rafter be 67.1” not 6ft 7 5/16”? Just wanting to confirm before I cut.
Reply
Scott
May 11, 2020 at 12:24 pm
I am adding the height of the wall frames up to 1.5″ short of 8′. What is the reason for that?
Reply
Alan Waterman
May 15, 2020 at 2:33 pm
The total height on the plans is 11′ 6″. Where I live, I can go up to 12′ without a permit. Is there any reason not to size the studs from 7′ 6″ to 7′ 9.5″ so that the total height with the double top and single bottom plates is 8′ even? It would allow using the full height siding without having to cut it.
Reply
Ron
July 28, 2020 at 8:50 pm
I plan on building this for a mini she shed work out area. Would anything need to be changed since I will insulate and run electric to it? I will install a regular door and two small windows. Thanks in advance. rg
Reply
Philippe Janicka
August 3, 2020 at 12:34 pm
I have several questions I would to pose all at once. I’m building the 10 x 12 shed with gable. I will be sheeting the outside walls and using lap siding that matches my house.
1) Would I sheet and side the shed prior to putting up the truss’ or put the truss’ up first or in between the sheeting and siding?
2) What is the best method for notching the rafters for the outriggers?
3) I live in Alaska, what is the snow load rating for this roof?Reply
Jay W.
August 6, 2020 at 6:14 am
I am in the process of building the 10 x 12 shed right now. I have the floor done, and all of the materials bought except for roofing supplies. I will build it with the single and double door as shown, but 3 windows for more natural light. I have a couple of basic questions, which looking at the traffic here likely will go unanswered by the time I’m done lol.
Do I really need the skids? I have them on, but I am thinking of removing them before I carry on. I don’t think I’ll ever move the shed, and it’s sitting on a 6″ gravel base that’s about 2-4″ above grass level already.
Do I have to flash the windows with tape and use silicone etc.? I suppose so to do a good job. I was just thinking about doing the bottom. Also, can I build the wall with the window in it on the ground before I raise it up? Seems like it would be easier.
I also intend to paint the floor with deckover, and leave off the roof overhang. I may run power wire to it while I can get at everything, but drilling into the side of it later shouldn’t be an issue.
I also need to anchor it, and using the screw in anchors seems easier especially without the skids underneath.
I will donate when I’m done because plans like this are $20 on Amazon or at a box store and the time and effort it took to share this plan is well worth it imho.
Reply
Dave E
August 12, 2020 at 3:42 pm
I plan on building this. Has anyone gone through the trouble of creating a BOM document with links to all the materials for purchase (primarily from Home Depot)? Also, anyone document this build on a video? If not, I may do both… TIA
Reply
Jay Wnuk
August 20, 2020 at 8:34 am
It’s going to vary based on the number of doors and windows you put in. I put in two 24 x 24 windows, and one 24 x 36 window, in addition to a single and a double door. I also put 2 x 4’s inside along the seams where the siding meets, as I felt the joint was a bit too weak otherwise. My siding did not always line up with a wall stud. Most of the list of materials above was accurate, if you don’t make mistakes with siding or flooring etc. I would say I’ve had to go out an buy an additional 24 or more 8 foot 2 x 4’s for windows and door trim, and I’ll have to buy more 1 x 4 trim boards to go around those.
As for cost I’m at around $2,500 currently. Considering that it’s 2020 in the midst of a pandemic and everyone seems to be out buying treated lumber and landscaping material just finding lumber readily available in the upper midwest was a challenge. Lumber is probably about $2k of the total, the rest is roofing material, door hardware, windows, loads of gravel base, etc.
I still think building your own is a far better value, if you don’t include your labor and view it as a fun project. Looking at the similarly built sheds at big box stores I was pricing them around $3,300 before tax and delivery etc. and you still need to make the foundation. I can tally up a BOM after I’m done, I still have to put the roof on and paint it etc.
Reply
Rob
August 12, 2020 at 7:14 pm
Any way to get these plans without a window?
Reply
Jay Wnuk
September 11, 2020 at 7:24 am
The plan itself does not include windows, that is a separate optional step, so all of the walls you build as shown do not have windows and are easier. I used 3 windows and 2 doors however, and it really helps natural light get in.
Reply
Shawn
September 17, 2020 at 11:29 am
What pitch is this roof?
Reply
July 8, 2021 at 3:35 pm
Tried to print the plans for a 10×12 shed but only the words printed an not the pictures! WHY?
Reply
December 30, 2021 at 5:05 pm
Foolproof. Thank you
Reply
Alex
February 20, 2022 at 9:30 am
What would be done for a foundation for this plan?
Reply
Sam
August 25, 2022 at 8:59 am
Pretty good plans. Although you will need more 3/4 flooring as 4 is not enough
Reply
Carl Fulton
December 28, 2022 at 9:16 am
Please send me plans.
Reply
David Batzel
July 7, 2023 at 2:41 pm
I plan to build!
Reply
dacotah wenninger
August 29, 2023 at 8:33 am
current minnesota prices for exact material list $3,500.09
Reply